Thursday, April 2, 2015

Touch screen DDS with AD9850 and Arduino

   With a touch screen display like this:
who work fine with SWTFT library from Smoke and WiresI write a sketch for a virtual keyboard... after some tests, I decided to use the DDS module with AD9850 (see article Signal generator with AD9850 and Arduino) together with this display and made a "touch screen DDS".
   Display is made as a shield for Arduino Uno/Mega boards and use a lot of outputs...
 I designed a intermediate shield for disconnect the microSD and connect the AD9850 module:
   Real, the and shield and modules:
   My sketch use library for control the display from Smoke and Wires and use info for control the AD9850 from http://webshed.org/wiki/AD9850_Arduino:
// Code for TFT shield display provided by Smoke And Wires
// http://www.smokeandwires.co.nz
// This code has been taken from the Adafruit TFT Library and modified
//  by us for use with our TFT Shields / Modules
// For original code / licensing please refer to
// https://github.com/adafruit/TFTLCD-Library

// adapted sketch by niq_ro from http://arduinotehniq.blogspot.com/
// http://nicuflorica.blogspot.ro/
// http://www.tehnic.go.ro
// http://www.niqro.3x.ro
// original virtual keyboard with DDS with AD8959 by niq_ro
// ver. 1m4a: 30.03.2015, Craiova - Romania

#include <Adafruit_GFX.h>    // Core graphics library
#include "SWTFT.h" // Hardware-specific library

// The control pins for the LCD can be assigned to any digital or
// analog pins...but we'll use the analog pins as this allows us to
// double up the pins with the touch screen (see the TFT paint example).
// #define LCD_CS A3 // Chip Select goes to Analog 3
// #define LCD_CD A2 // Command/Data goes to Analog 2
// #define LCD_WR A1 // LCD Write goes to Analog 1
// #define LCD_RD A0 // LCD Read goes to Analog 0

// #define LCD_RESET A4 // Can alternately just connect to Arduino's reset pin

// When using the BREAKOUT BOARD only, use these 8 data lines to the LCD:
// For the Arduino Uno, Duemilanove, Diecimila, etc.:
//   D0 connects to digital pin 8  (Notice these are
//   D1 connects to digital pin 9   NOT in order!)
//   D2 connects to digital pin 2
//   D3 connects to digital pin 3
//   D4 connects to digital pin 4
//   D5 connects to digital pin 5
//   D6 connects to digital pin 6
//   D7 connects to digital pin 7
// For the Arduino Mega, use digital pins 22 through 29
// (on the 2-row header at the end of the board).

#include <TouchScreen.h>


#define YP A1  // must be an analog pin, use "An" notation!
#define XM A2  // must be an analog pin, use "An" notation!
#define YM 7   // can be a digital pin
#define XP 6   // can be a digital pin

#define TS_MINX 150
#define TS_MINY 120
#define TS_MAXX 920
#define TS_MAXY 940

// For better pressure precision, we need to know the resistance
// between X+ and X- Use any multimeter to read it
// For the one we're using, its 300 ohms across the X plate
TouchScreen ts = TouchScreen(XP, YP, XM, YM, 300);

// Assign human-readable names to some common 16-bit color values:
#define BLACK   0x0000
#define BLUE    0x001F
#define RED     0xF800
#define GREEN   0x07E0
#define CYAN    0x07FF
#define MAGENTA 0xF81F
#define YELLOW  0xFFE0
#define WHITE   0xFFFF
#define ROZ     0xFBE0
#define GRI     0xBDF7
// http://stackoverflow.com/questions/13720937/c-defined-16bit-high-color
// http://wiibrew.org/wiki/U16_colors

SWTFT tft;

#define BOXSIZE 80
#define BOXSIZE2 60
#define PENRADIUS 3

int ics; 
int numar, ics0, igr0, pas; 

#include <EEPROM.h>
long n1, n2, n3, n4, n5, n6, n7, n8; // number for frequency;
long frecv; // value for frecvency;
byte cifru; 

//Setup some items
//#define W_CLK 13   // Pin 13 - connect to AD9850 module word load clock pin (CLK)
#define CLOCK 13
//#define FQ_UD 12   // Pin 12 - connect to freq update pin (FQ)
#define LOAD 12
#define DATA 11   // Pin 11 - connect to serial data load pin (DATA)
#define RESET 10  // Pin 10 - connect to reset pin (RST) 
//#define pulseHigh(pin) {digitalWrite(pin, HIGH); digitalWrite(pin, LOW); }
#define DDS_CLOCK 125000000 // http://webshed.org/wiki/AD9850_Arduino
//#define DDS_CLOCK 125000000

void setup(void) {

pinMode (DATA,  OUTPUT); 
pinMode (CLOCK, OUTPUT); 
pinMode (LOAD,  OUTPUT); 
pinMode (RESET, OUTPUT); 
  
AD9850_init();
AD9850_reset();
//SetFrequency(15000);
zaibar();
SetFrequency(frecv);
  
  Serial.begin(9600);
  Serial.print(F("DDS with AD9850 "));
  Serial.println("made by niq_ro");
  
  tft.reset();
  
  uint16_t identifier = tft.readID();

  Serial.print(F("LCD driver chip: "));
  Serial.println(identifier, HEX);
 
  tft.begin(identifier);

  tft.fillScreen(BLACK);
  tft.fillRect(0, 0, 320, 240, BLACK);
//  tft.setRotation(0);
//  tft.setCursor(5, 100);
  tft.setTextColor(RED);  tft.setTextSize(2);
//  tft.println("Acces control");
  tft.setCursor(30, 120);
  tft.println("DDS with AD9850");
  tft.setCursor(20, 150);
  tft.setTextColor(YELLOW);
  tft.println("on touch display");
  tft.setCursor(70, 180);
  tft.setTextColor(BLUE);
  tft.println("by niq_ro");
  tft.setCursor(75, 210);
  tft.setTextColor(ROZ);
  tft.println("ver. 1.4a");
  

delay(2000);
tft.fillRect(0, 0, 320, 240, BLACK);

numar = 0;
ics0 = 10;
igr0 = 280;
pas = 18;
frecv = 0;
  
//tft.setRotation(0);
 stergere ();

 cifre ();
 caractere();

}

#define MINPRESSURE 10
#define MAXPRESSURE 1000


void loop()
{
    
  // Recently Point was renamed TSPoint in the TouchScreen library
  // If you are using an older version of the library, use the
  // commented definition instead.
  // Point p = ts.getPoint();
  TSPoint p = ts.getPoint();

  // if sharing pins, you'll need to fix the directions of the touchscreen pins
  //pinMode(XP, OUTPUT);
  pinMode(XM, OUTPUT);
  pinMode(YP, OUTPUT);
  //pinMode(YM, OUTPUT);

  // we have some minimum pressure we consider 'valid'
  // pressure of 0 means no pressing!

  if (p.z > MINPRESSURE && p.z < MAXPRESSURE) {
  //   tft.setTextSize(4);
     // scale from 0->1023 to tft.width
    p.x = tft.width()-(map(p.x, TS_MINX, TS_MAXX, tft.width(), 0));
    p.y = tft.height()-(map(p.y, TS_MINY, TS_MAXY, tft.height(), 0));
 
    if (p.y < BOXSIZE2) {   // fist line (0, 1 & 2)
         if (p.x < BOXSIZE) { 
         tft.fillRect(0, 0, BOXSIZE, BOXSIZE2, GRI); // one       
         tft.setTextColor(BLACK);
         tft.setCursor(30, 20);
         tft.println("1");
 //        caracter(1);
int ics1 = ics0+pas*numar;
caracters(1,ics1,igr0);
cifru = 1;
         delay (200);
         tft.fillRect(0, 0, BOXSIZE, BOXSIZE2, RED); // one       
         tft.setTextColor(WHITE);
         tft.setCursor(30, 20);
         tft.println("1");

       } else if (p.x < BOXSIZE*2) {
         tft.fillRect(BOXSIZE, 0, BOXSIZE, BOXSIZE2, GRI);  // two
         tft.setTextColor(BLACK);
         tft.setCursor(110, 20);
         tft.println("2");
//         caracter(2);
int ics1 = ics0+pas*numar;
caracters(2,ics1,igr0);
cifru = 2;
         delay (200);
         tft.fillRect(BOXSIZE, 0, BOXSIZE, BOXSIZE2, YELLOW);  // two
         tft.setTextColor(BLACK);
         tft.setCursor(110, 20);
         tft.println("2");
         
        } else if (p.x < BOXSIZE*3) {
         tft.fillRect(BOXSIZE*2, 0, BOXSIZE, BOXSIZE2, GRI); // three
         tft.setTextColor(BLACK);
         tft.setCursor(190, 20);
         tft.println("3");
//         caracter(3);
int ics1 = ics0+pas*numar;
caracters(3,ics1,igr0);
cifru = 3;
         delay (200);
         tft.fillRect(BOXSIZE*2, 0, BOXSIZE, BOXSIZE2, BLUE); // three
         tft.setTextColor(WHITE);
         tft.setCursor(190, 20);
         tft.println("3");
       }
   //      numar = numar + 1;
    }
    
  if ((p.y < BOXSIZE2*2) && (p.y > BOXSIZE2)) {   // second line (4, 5 & 6)
         if (p.x < BOXSIZE) { 
         tft.fillRect(0, BOXSIZE2, BOXSIZE, BOXSIZE2, GRI); // four       
         tft.setTextColor(BLACK);
         tft.setCursor(30, 80);
         tft.println("4");
int ics1 = ics0+pas*numar;
caracters(4,ics1,igr0);
cifru = 4;
//         caracter(4);
         delay (200);
         tft.fillRect(0, BOXSIZE2, BOXSIZE, BOXSIZE2, CYAN); // four 
         tft.setTextColor(BLACK);
         tft.setCursor(30, 80);
         tft.println("4");

       } else if (p.x < BOXSIZE*2) {
         tft.fillRect(BOXSIZE, BOXSIZE2, BOXSIZE, BOXSIZE2, GRI);  // five
         tft.setTextColor(BLACK);
         tft.setCursor(110, 80);
         tft.println("5");
int ics1 = ics0+pas*numar;
caracters(5,ics1,igr0);
cifru = 5;
//         caracter(5);
         delay (200);
         tft.fillRect(BOXSIZE, BOXSIZE2, BOXSIZE, BOXSIZE2, GREEN);  // five
         tft.setTextColor(BLACK);
         tft.setCursor(110, 80);
         tft.println("5");
         
        } else if (p.x < BOXSIZE*3) {
         tft.fillRect(BOXSIZE*2, BOXSIZE2, BOXSIZE, BOXSIZE2, GRI); // six
         tft.setTextColor(BLACK);
         tft.setCursor(190, 80);
         tft.println("6");
int ics1 = ics0+pas*numar;
caracters(6,ics1,igr0);
cifru = 6;
//         caracter(6);
         delay (200);
         tft.fillRect(BOXSIZE*2, BOXSIZE2, BOXSIZE, BOXSIZE2, MAGENTA); // six
         tft.setTextColor(WHITE);
         tft.setCursor(190, 80);
         tft.println("6");
       }
    //     numar = numar + 1;
  }

if ((p.y < BOXSIZE2*3) && (p.y > BOXSIZE2*2)) {   // second line (7, 8 & 9)
         if (p.x < BOXSIZE) { 
         tft.fillRect(0, BOXSIZE2*2, BOXSIZE, BOXSIZE2, GRI); // four       
         tft.setTextColor(BLACK);
         tft.setCursor(30, 140);
         tft.println("7");
int ics1 = ics0+pas*numar;
caracters(7,ics1,igr0);
cifru = 7;
//         caracter(7);
         delay (200);
         tft.fillRect(0, BOXSIZE2*2, BOXSIZE, BOXSIZE2, RED); // four 
         tft.setTextColor(WHITE);
         tft.setCursor(30, 140);
         tft.println("7");

       } else if (p.x < BOXSIZE*2) {
         tft.fillRect(BOXSIZE, BOXSIZE2*2, BOXSIZE, BOXSIZE2, GRI);  // five
         tft.setTextColor(BLACK);
         tft.setCursor(110, 140);
         tft.println("8");
int ics1 = ics0+pas*numar;
caracters(8,ics1,igr0);
cifru = 8;
//         caracter(8);
         delay (200);
         tft.fillRect(BOXSIZE, BOXSIZE2*2, BOXSIZE, BOXSIZE2, YELLOW);  // five
         tft.setTextColor(BLACK);
         tft.setCursor(110, 140);
         tft.println("8");
         
        } else if (p.x < BOXSIZE*3) {
         tft.fillRect(BOXSIZE*2, BOXSIZE2*2, BOXSIZE, BOXSIZE2, GRI); // six
         tft.setTextColor(BLACK);
         tft.setCursor(190, 140);
         tft.println("9");
//         caracter(9);
int ics1 = ics0+pas*numar;
caracters(9,ics1,igr0);
cifru = 9;
         delay (200);
         tft.fillRect(BOXSIZE*2, BOXSIZE2*2, BOXSIZE, BOXSIZE2, BLUE); // six
         tft.setTextColor(WHITE);
         tft.setCursor(190, 140);
         tft.println("9");
       }
  //       numar = numar + 1;
 }

if ((p.y < BOXSIZE2*4) && (p.y > BOXSIZE2*3)) {   // second line (*, 0 & #)
/*
       if (p.x < BOXSIZE) { 
         tft.fillRect(0, BOXSIZE2*3, BOXSIZE, BOXSIZE2, GRI); // four       
         tft.setTextColor(BLACK);
         tft.setCursor(30, 200);
         tft.println("*");
int ics1 = ics0+pas*numar;
caracters(10,ics1,igr0);
//         caracter(10);
         delay (200);
         tft.fillRect(0, BOXSIZE2*3, BOXSIZE, BOXSIZE2, CYAN); // four 
         tft.setTextColor(BLACK);
         tft.setCursor(30, 200);
         tft.println("*");

       } else
   */   
       if ((p.x > BOXSIZE) && (p.x < BOXSIZE*2))  {
         tft.fillRect(BOXSIZE, BOXSIZE2*3, BOXSIZE, BOXSIZE2, GRI);  // five
         tft.setTextColor(BLACK);
         tft.setCursor(110, 200);
         tft.println("0");
//         caracter(0);
int ics1 = ics0+pas*numar;
caracters(0,ics1,igr0);
cifru = 0;
         delay (200);
         tft.fillRect(BOXSIZE, BOXSIZE2*3, BOXSIZE, BOXSIZE2, GREEN);  // five
         tft.setTextColor(BLACK);
         tft.setCursor(110, 200);
         tft.println("0");
         
        }
 /*
        else if (p.x < BOXSIZE*3) {
         tft.fillRect(BOXSIZE*2, BOXSIZE2*3, BOXSIZE, BOXSIZE2, GRI); // six
         tft.setTextColor(BLACK);
         tft.setCursor(190, 200);
         tft.println("#");
int ics1 = ics0+pas*numar;
caracters(11,ics1,igr0);
//         caracter(11);
         delay (200);
         tft.fillRect(BOXSIZE*2, BOXSIZE2*3, BOXSIZE, BOXSIZE2, MAGENTA); // six
         tft.setTextColor(WHITE);
         tft.setCursor(190, 200);
         tft.println("#");
       }
*/       
       
// numar = numar + 1;
     }
//caractere();

  numar = numar + 1;
memorie(cifru,numar);
Serial.print(cifru);

  if (numar == 2) numar = numar +1;
  if (numar == 6) numar = numar +1;

  if (numar == 10) {
    tft.setTextColor(YELLOW);
     tft.setTextSize(3);
         tft.setCursor(200, 250);
         tft.println("ok");

 Serial.print(" --> "); 
// read eeprom memory and calculate the stored number (freqvency)
zaibar(); 

 Serial.print(frecv);
 Serial.println("Hz");
 Serial.println("---------");
  Serial.print(frecv);
/*
  Serial.println(frecv);
          Serial.println("---------");
          for (int j=11; j<19; j++)
          {
           Serial.print(EEPROM.read(j));
          }
 */
   delay (3000);
 tft.fillRect(0, 310 , 239, 5, BLACK);   // for testing   
 tft.fillRect(199, 249 , pas*2+2, 30, BLACK);   // for testing   
//   caractere();
   numar = 0;
        
  }
  }

  
}  // end main loop


void cifre ()
{
// number for "buttons"
 tft.setTextSize(4);
 tft.setTextColor(WHITE);
 tft.setCursor(30, 20);
 tft.println("1");
 tft.setTextColor(BLACK);
 tft.setCursor(110, 20);
 tft.println("2");
 tft.setTextColor(WHITE);
 tft.setCursor(190, 20);
 tft.println("3");
 tft.setTextColor(BLACK);
 tft.setCursor(30, 80);
 tft.println("4");
 tft.setTextColor(BLACK);
 tft.setCursor(110, 80);
 tft.println("5");
 tft.setTextColor(WHITE);
 tft.setCursor(190, 80);
 tft.println("6");
 tft.setTextColor(WHITE);
 tft.setCursor(30, 140);
 tft.println("7");
 tft.setTextColor(BLACK);
 tft.setCursor(110, 140);
 tft.println("8");
 tft.setTextColor(WHITE);
 tft.setCursor(190, 140);
 tft.println("9");
// tft.setTextColor(BLACK);
// tft.setCursor(30, 200);
// tft.println("*");
 tft.setTextColor(BLACK);
 tft.setCursor(110, 200);
 tft.println("0");
// tft.setTextColor(WHITE);
// tft.setCursor(190, 200);
// tft.println("#");
}

void stergere ()
{
//      Serial.println("erase");
// firs line
  tft.fillRect(0, 0, BOXSIZE, BOXSIZE2, RED); // one
  tft.fillRect(BOXSIZE, 0, BOXSIZE, BOXSIZE2, YELLOW);  // two
  tft.fillRect(BOXSIZE*2, 0, BOXSIZE, BOXSIZE2, BLUE); // three
// second line
  tft.fillRect(0, BOXSIZE2 , BOXSIZE, BOXSIZE2, CYAN);  // four
  tft.fillRect(BOXSIZE, BOXSIZE2, BOXSIZE, BOXSIZE2, GREEN);  // five
  tft.fillRect(BOXSIZE*2, BOXSIZE2, BOXSIZE, BOXSIZE2, MAGENTA);  // six
// 3rd line
  tft.fillRect(0, BOXSIZE2*2 , BOXSIZE, BOXSIZE2, RED);  // seven
  tft.fillRect(BOXSIZE, BOXSIZE2*2, BOXSIZE, BOXSIZE2, YELLOW);  // eight
  tft.fillRect(BOXSIZE*2, BOXSIZE2*2, BOXSIZE, BOXSIZE2, BLUE);  // nein
// 4th line
//  tft.fillRect(0, BOXSIZE2*3 , BOXSIZE, BOXSIZE2, CYAN);  // *
  tft.fillRect(BOXSIZE, BOXSIZE2*3, BOXSIZE, BOXSIZE2, GREEN);  // zero
//  tft.fillRect(BOXSIZE*2, BOXSIZE2*3, BOXSIZE, BOXSIZE2, MAGENTA);  // #

  cifre ();  
    }

void caracter (int numar)
{
 tft.setTextSize(4);
 tft.setTextColor(WHITE);
 tft.setCursor(110, 280);
 tft.fillRect(0, 260 , 240, 59, BLACK);  // *
if (numar == 0) tft.println("0");
if (numar == 1) tft.println("1");
if (numar == 2) tft.println("2");
if (numar == 3) tft.println("3");
if (numar == 4) tft.println("4");
if (numar == 5) tft.println("5");
if (numar == 6) tft.println("6");
if (numar == 7) tft.println("7");
if (numar == 8) tft.println("8");
if (numar == 9) tft.println("9");
//if (numar == 10) tft.println("*");
//if (numar == 11) tft.println("#");
}

void caractere()
{
 tft.setTextSize(2);
tft.fillRect(0, 241 , 240, 79, BLACK);  // *
 tft.setTextColor(WHITE);
 tft.setCursor(10, 258);
 tft.println("DDS with AD9850");
 tft.setTextSize(3);
 tft.setCursor(10, 280);
// tft.println("??.???.???Hz");
citiremem();
// tft.println(EEPROM.read(11)); 
}

void caracters (int numar, int ics, int igr)
{
 tft.setTextSize(3);
 tft.setTextColor(WHITE);
//tft.drawLine(x1, y1, x2, y2, color); // line model
 tft.drawLine(ics, igr+32, ics+pas, igr+32, BLUE);


 tft.setCursor(ics, igr);
 tft.fillRect(ics, igr-2 , pas, 30, YELLOW);   // for testing
 delay(100);
 tft.fillRect(ics, igr-2 , pas, 30, BLACK);  

if (numar == 0) tft.println("0");
if (numar == 1) tft.println("1");
if (numar == 2) tft.println("2");
if (numar == 3) tft.println("3");
if (numar == 4) tft.println("4");
if (numar == 5) tft.println("5");
if (numar == 6) tft.println("6");
if (numar == 7) tft.println("7");
if (numar == 8) tft.println("8");
if (numar == 9) tft.println("9");
//if (numar == 10) tft.println("*");
//if (numar == 11) tft.println("#");
tft.setTextSize(4);
}


void memorie (byte cifra, int pozitie)
{
  if (pozitie == 1) {
    EEPROM.write(11,cifra); // cifra zeci de MHz
  //  Serial.print(EEPROM.read(11));
  }
  if (pozitie == 2) {
    EEPROM.write(12,cifra); // cifra MHZ
 //   Serial.print(EEPROM.read(12));
  }  
  if (pozitie == 4) {
    EEPROM.write(13,cifra); // cifra sute de kHz
//   Serial.print(EEPROM.read(13));
  }
  if (pozitie == 5) {
    EEPROM.write(14,cifra); // cifra zeci de kHz
 //   Serial.print(EEPROM.read(14));
  }
  if (pozitie == 6) {
    EEPROM.write(15,cifra); // cifra kHz
 //   Serial.print(EEPROM.read(15));
  }   
  if (pozitie == 8) {
    EEPROM.write(16,cifra); // cifra sute de Hz
  //  Serial.print(EEPROM.read(16));
  }
  if (pozitie == 9) {
    EEPROM.write(17,cifra); // cifra zeci de Hz
 //   Serial.print(EEPROM.read(17));
  }
  if (pozitie == 10) {
    EEPROM.write(18,cifra); // cifra Hz
 //   Serial.print(EEPROM.read(18));
  }
}

void citiremem ()
{
//tft.setTextSize(3);
// tft.setCursor(10, 280);
 for (int ji=11; ji<19; ji++)
{
  int nr = EEPROM.read(ji);

if (nr == 0) tft.print("0");
if (nr == 1) tft.print("1");
if (nr == 2) tft.print("2");
if (nr == 3) tft.print("3");
if (nr == 4) tft.print("4");
if (nr == 5) tft.print("5");
if (nr == 6) tft.print("6");
if (nr == 7) tft.print("7");
if (nr == 8) tft.print("8");
if (nr == 9) tft.print("9");

if (ji==12) tft.print(".");
if (ji==15) tft.print(".");
}
tft.println("Hz");
}


void SetFrequency(unsigned long frequency)
{
  unsigned long tuning_word = (frequency * pow(2, 32)) / DDS_CLOCK;
  digitalWrite (LOAD, LOW); 

  shiftOut(DATA, CLOCK, LSBFIRST, tuning_word);
  shiftOut(DATA, CLOCK, LSBFIRST, tuning_word >> 8);
  shiftOut(DATA, CLOCK, LSBFIRST, tuning_word >> 16);
  shiftOut(DATA, CLOCK, LSBFIRST, tuning_word >> 24);
  shiftOut(DATA, CLOCK, LSBFIRST, 0x0);
  digitalWrite (LOAD, HIGH); 
}

void AD9850_init()
{

  digitalWrite(RESET, LOW);
  digitalWrite(CLOCK, LOW);
  digitalWrite(LOAD, LOW);
  digitalWrite(DATA, LOW);
}

void AD9850_reset()
{
  //reset sequence is:
  // CLOCK & LOAD = LOW
  //  Pulse RESET high for a few uS (use 5 uS here)
  //  Pulse CLOCK high for a few uS (use 5 uS here)
  //  Set DATA to ZERO and pulse LOAD for a few uS (use 5 uS here)

  // data sheet diagrams show only RESET and CLOCK being used to reset the device, but I see no output unless I also
  // toggle the LOAD line here.

  digitalWrite(CLOCK, LOW);
  digitalWrite(LOAD, LOW);

  digitalWrite(RESET, LOW);
  delay(5);
  digitalWrite(RESET, HIGH);  //pulse RESET
  delay(5);
  digitalWrite(RESET, LOW);
  delay(5);

  digitalWrite(CLOCK, LOW);
  delay(5);
  digitalWrite(CLOCK, HIGH);  //pulse CLOCK
  delay(5);
  digitalWrite(CLOCK, LOW);
  delay(5);
  digitalWrite(DATA, LOW);    //make sure DATA pin is LOW

  digitalWrite(LOAD, LOW);
  delay(5);
  digitalWrite(LOAD, HIGH);  //pulse LOAD
  delay(5);
  digitalWrite(LOAD, LOW);
  // Chip is RESET now
}


void zaibar()
{
 n1 = EEPROM.read(11); //Serial.print(n1);
 n2 = EEPROM.read(12); //Serial.print(n2);
 n3 = EEPROM.read(13); //Serial.print(n3);
 n4 = EEPROM.read(14); //Serial.print(n4);
 n5 = EEPROM.read(15); //Serial.print(n5);
 n6 = EEPROM.read(16); //Serial.print(n6);
 n7 = EEPROM.read(17); //Serial.print(n7);
 n8 = EEPROM.read(18); //Serial.print(n8);
 frecv = n1*10000000 + n2*1000000+n3*100000+n4*10000+n5*1000+n6*100+n7*10+n8;
}  
   For measure the freqvency I made a simple freqvencymeter with Arduino, using info from interface.khm.de:
   I made a movie named Touch screen DDS with AD9850

9 comments:

  1. I was very interested to read your blog as I have some experience of fixing computers and this is an area I would like to learn more about. I think it's great that you managed to make a touch screen. It's a very cool and insetting thing to do.I look forward to reading more of your blog in the future.

    Raymond @ CKS Global Solutions LTD

    ReplyDelete
  2. I have very little experience when it comes to electronics and programming but this is indeed very interesting to read, especially coming from someone like yourself who has a great deal of knowledge. This is something I want to get my son into as there is a huge need for a skill set such as this.

    Brian Hopkins @ Micro Tips USA

    ReplyDelete
  3. Interactive digital signage, hdmi touch screen,industrial touch screen monitors

    Southern Stars Enterprises Co Ltd is the specialist manufacturer for commercial display since 1996.All our products are heavy-duty built to suit super long hour loop-playing 24/7/365. As one of touch screen monitor supplier, we have 15,19,22,32,42,55 inch commercial touch screen desktop monitor, industrial touch panel, touch screen monitor hdmi, retail chain store interactive digital signage, super market wall mounted hdmi touch screen,restaurant 16:9 industrial touch screen monitors etc.

    Visit here:- Touch screen monitor

    ReplyDelete
  4. Thanks for sharing such a piece of useful information among us. keep sharing this kind of information.

    Do you want to buy a high-quality IR Touch Monitor at the best price? if yes then order online now. Obeytec Infrared Touch Monitor Or IR Touch Monitor Is Designed Specially For Smart Touch Applications Use In Public. We Have Three Main Series Ir Touch Monitors. Metal Chassis Touch Monitor, Open Frame No Front Cover, Wall Mount Ir Touch Monitors, Etc. Call us on +86 134 8064 0976, +86 158 1825 2430 for further details about the product.

    ReplyDelete
  5. Nice Blog, Thanks for sharing with us. Keep Sharing!!

    Do you want to buy Interactive Displays (IR Touch) Online?

    Buy Interactive Displays (IR Touch) Online

    ReplyDelete
  6. Nice Blog, Thanks for sharing with. Keep sharing!!

    Do you want to buy High Brightness IR Touch Monitors Online?

    Buy High Brightness IR Touch Monitors Online

    ReplyDelete
  7. The versatility of industrial touchscreens enables operators to make quick adjustments, improving productivity and reducing downtime.
    industrial touchscreen displays

    ReplyDelete
  8. Nice Blog, Thanks for sharing with us! Keep Sharing.

    Do you want to buy Resistive Touch Monitors online at affordable rate?


    Buy Resistive Touch Monitors

    ReplyDelete
  9. One of the key advantages of industrial touchscreen panels is their versatility in supporting various applications across industries, from manufacturing and automation to healthcare and transportation.

    ReplyDelete